Having a bathtub with jets is a satisfying luxury that I hope everyone can experience. If your bathtub jets won’t turn off, you must get to the root cause. Bathtub jets normally work with no interruptions. They are supposed to have a consistent flow for optimal function.
Bathtub jets won’t turn off? The problem may be due to the dysfunction of the breaker. It may also be due to the jets’ active filtration cycle. The breaker linked to the bathroom must be reset. The jets must be cleaned and you should let them cycle for several minutes.
I’m sure if your bathtub jets are malfunctioning, you are eager to fix the issue! Read on to find out what you can do when your bathtub jets won’t turn off.
Step-By-Step Instructions for Shutting Off Bathtub Jets
1. Allow the Filtration Cycle to Run for Several Minutes
If you cannot shut off your bathtub jets, try waiting for several minutes until the filtration cycle finishes. You might be wondering what the filtration cycle has to do with the bathtub jets shutting off. It’s important to understand this concept to ensure you maintain your bathtub well.
Why is my Bathtub Jets’ Filtration Cycle Important?
Jets shoot out water that must be cleaned properly before it comes out. They have a built-in mechanism that allows them to stay regulated for proper function. When the filtration cycle is active, you will notice that the jets will run for their entirety.
Once the cycle is complete, the jets will shut off and the bathtub will be ready for its next use. You must let the filtration cycle run its course and allow the jets to run. It only takes a brief moment for the cycle to complete. This part of your bathtub’s maintenance will keep your jets running smoothly.
However, if you notice that the filtration cycle takes more than several minutes, there’s a problem. When the jets continue to run longer than the time it takes to complete the filtration cycle, it could mean there’s an issue with the breaker. Oftentimes, the breaker is the root cause of malfunctioning jets.
2. Reset Your Bathtub’s Circuit Breaker
Once you determine that the jets continue to run after the filtration cycle is complete, investigate the circuit breaker. Find out which breaker in your electrical panel directs your bathtub.
Oftentimes, circuit breakers are the culprit of most problems with your bathtub. Electricity must flow into your bathroom without interruptions for your bathtub to function properly.
Resetting the circuit breaker when your bathtub jets won’t turn off is an easy fix. When the circuit breaker is reset, the bathtub jets will immediately shut off. Taking this step will give you the chance to inspect the bathtub for other potential issues.
Perhaps the jets are not shutting off for a different reason. Or, the malfunction could be due to a combination of issues. Either way, resetting the circuit breaker is an essential step while you’re troubleshooting this problem.
3. Ensure the Jets Are Clean
Ensuring your jets are clean is part of the normal maintenance of your bathtub. The perfect time to inspect the jets for cleanliness is while you are resetting the circuit breaker.
To inspect the cleanliness of your bathtub jets, simply wipe them. You may use a damp cloth along with a gentle cleaning solution. Be sure to check for debris, dust, and any other foreign particles.
The jets are supposed to be cleaned regularly for optimum function. You certainly don’t want lingering debris to cause a different issue in the future. Although uncleaned jets may not be the reason for them not shutting off, it is still an important part of maintenance.
Taking your bathtub’s maintenance seriously will allow you to enjoy it without issues for many years. For a more detailed bathtub cleaning routine (https://www.apartmenttherapy.com/how-to-clean-bathtub-jets-with-basic-household-ingredients-207786), follow these steps using common household ingredients:
Turn on the water and let the tub fill until the jets are covered. Use hot water and cover the jets by two to three inches.
Mix half a cup of vinegar with two tablespoons of dishwashing soap. Some people use bleach (https://www.bobvila.com/articles/how-to-clean-a-jetted-tub/) instead of vinegar, but it can potentially dry out the internal gaskets.
Turn on the bathtub jets and let them run for approximately 15 minutes.
Empty the water from the tub and fill it up back again with cold water. Run the jets again for about 10 minutes.
Empty the water once more and rinse the whole tub and jets well. Make sure all buildup is removed.
For a deeper clean, you can scrub the jets with a soft brush or a cloth that is not abrasive.
Remember to check the jet covers for buildup gunk. If you find any buildup, use dental floss to reach behind the jet covers.
Note: When you’re ready to clean the jets for the first time, read the manufacturer’s manual for instructions.
4. Test the Bathtub Jets for Normal Function
The final step you’ll want to take is to test your bathtub jets. Check them to see if they turn on and off as they normally do. Hopefully, after running a filtration cycle, resetting the circuit breaker, and cleaning the jets, they will now turn off.
If they do turn off, then you’ll want to press the on/off switch a few times to help the bathtub completely reset. It is a final step that helps the bathtub have a complete mechanical refresh.
In some cases, the bathtub jets shut off and don’t come back on. To avoid this, it is essential that you reset all components. Running the on/off switch through a few cycles will ensure that the whole machine starts to operate normally again.
As you can see, troubleshooting your bathtub jets is simple. Most importantly, it is an effective way to keep your bathtub running properly.
Quick Recap
Now, let’s recap what you’ve learned! If you notice your bathtub jets are not turning off, you must detect the root cause. First, check to see if you simply have to wait for the filtration cycle to complete. In several minutes, you’ll find out if your jets will turn on following the filtration cycle.
If waiting for the filtration cycle to finish doesn’t do the trick, reset the circuit breaker. A faulty connection may be the root cause. Once the jets run for a few minutes, try resetting the circuit breaker.
As you reset the circuit breaker, take the opportunity to clean the jets. Once you have removed all debris and other particles, check for proper function. In most cases, this is enough to get your bathtub up and running as it normally does.
The number one reason jets don’t turn off is that the filtration cycle has to finish. That is the main root cause and the easiest to resolve. The jets will simply turn off on their own without any effort on your part.
Note: Be sure your bathroom follows the proper electrical code requirements (https://www.thespruce.com/easily-wire-a-bathroom-1152676) to ensure your home’s safety.
The second reason is the need to reset the circuit breaker. Another easy fix! Fortunately, troubleshooting your bathtub jets is quick and simple.
Get Ready For a Luxurious Bath!
When your bathtub malfunctions, getting back into a luxurious bath becomes a priority. I know it would for me!
There are several things you can do to maintain your bathtub in proper order and avoid problems. By following these simple steps when your bathtub jets won’t turn off, you’ll have a good chance to get them to function properly again.
Proper maintenance will prevent you from unnecessary repair calls. Now that you know more about your bathtub jets, you are very likely to be able to fix common issues such as this one. It pays to become familiar with your bathtub’s components.
So, grab your rubber ducky and get back in the tub!
Leave a comment